vbs中有如下類型數據，如何向金字塔公式系統傳遞？

dc := 1000;
VARIABLE:openPrice2[dc]=0;
<%

vOpenPrice2 = ffl.vardata("openPrice2")

'對vOpenPrice2數組中每個元素進行計算處理并賦值

'......

ffl.vardata("openPrice2") = vOpenPrice2

%>

請問以上寫法正確嗎？

openPrice := open;
highPrice := high;
lowPrice := low;
closePrice := close;
dc := 1000;
VARIABLE:openPrice2[dc]=0,highPrice2[dc]=0,lowPrice2[dc]=0,closePrice2[dc]=0;
<%
vOpenPrice = ffl.vardata("openPrice")
vHighPrice = ffl.vardata("highPrice")
vLowPrice = ffl.vardata("lowPrice")
vClosePrice = ffl.vardata("closePrice")
last = ubound(vOpenPrice)
vo = 0
vh = 0
vl = 0
vc = 0
i = 1
j = 0
dim openPriceArray(1000)
dim highPriceArray(1000)
dim lowPriceArray(1000)
dim closePriceArray(1000)
do while(i <= last)
  if ((vOpenPrice(i) > vClosePrice(i)) and (vOpenPrice(i-1) < vClosePrice(i-1))) then '前面一根是陽線，后面連續陰線 
  vo = vOpenPrice(i)
  vh = vHighPrice(i)
  vl = vLowPrice(i)
  vc = vClosePrice(i) 
  i = i + 1 
  do until ((vOpenPrice(i+1) < vClosePrice(i+1)) or (i > 1000)) '連續陰線直到遇到陽線為止
    vc = vClosePrice(i)   
    if (vHighPrice(i) > vh) then
      vh = vHighPrice(i)
    end if   
    if (vLowPrice(i) < vl) then
      vl = vLowPrice(i)
    end if   
    i = i + 1 
  loop 
  openPriceArray(j) = vo
  highPriceArray(j) = vh
  lowPriceArray(j) = vl
  closePriceArray(j) = vc 
  j = j + 1       
  end if
  if ((vOpenPrice(i) < vClosePrice(i)) and (vOpenPrice(i-1) > vClosePrice(i-1))) then '前面一根是陰線，后面連續陽線 
  vo = vOpenPrice(i)
  vh = vHighPrice(i)
  vl = vLowPrice(i)
  vc = vClosePrice(i) 
  i = i + 1 
  do until ((vOpenPrice(i+1) > vClosePrice(i+1)) or (i > 1000)) '連續陽線直到遇到陰線為止
    vc = vClosePrice(i)   
    if (vHighPrice(i) > vh) then
      vh = vHighPrice(i)
    end if   
    if (vLowPrice(i) < vl) then
      vl = vLowPrice(i)
    end if   
    i = i + 1 
  loop 
  openPriceArray(j) = vo
  highPriceArray(j) = vh
  lowPriceArray(j) = vl
  closePriceArray(j) = vc 
  j = j + 1       
  end if 
loop
ffl.vardata("openPrice2") = openPriceArray
ffl.vardata("highPrice2") = highPriceArray
ffl.vardata("lowPrice2") = lowPriceArray
ffl.vardata("closePrice2") = closePriceArray
%>
//KLINE(openPrice,highPrice,lowPrice,closePrice,1);
KLINE(openPrice2,highPrice2,lowPrice2,closePrice2,1);

采用這種方式，編譯通不過，提示“未定義的變量：OPENPRICE2”!請問問題出在哪兒了？

你的數組用法是有問題的，因為定義的數組與序列變量還是有些區別

openPrice2:=c;
highPrice2:=c;
lowPrice2:=c;
closePrice2:=c;

你這樣定義這4個變量為序列變量酒可以解決了